The primer that ensures a perfect base for topcoat.
This primer can be applied to Steel, Aluminum and Various Plastics
(PVC, PPO/PA, ABS, ABS/PC, PC/PBT, PE, PP, FRP or Blends such as PP/EPDM)
High Build Formula Sands Easily and Fills in Imperfections.
Fast Drying Acrylic Epoxy Formula.
Can be top coated with most quality 1K, 2K, Solvent-Based and Waterbourne Paints.
Please read and fully understand the instructions and warnings on the back of this can before use
Always wear proper Personal Protection Equipment and in a well ventilated area
Black – 500ml Fill
Apply up to 2-3 coats (Allow 5-10 mins between each coat) Optimum Application temperature is 64-77F at 40-50% Humidity Tack Free 7-10 Minutes, Sand after 60 Mins Can be top coated with all 1K, 2K, Solvent based and Waterbourne Paints Wet Sand or Dry Sand with P400-P600
*Note: Specifications are approximate and subject to change.
Rated 5 out of 5 by Nilsendj from good solutionA good solution for minor warps in my sheet metal, we welded in trim holes and the metal warped a little.
Date published: 2023-11-16
Rated 1 out of 5 by TomM from Good product, poor deliveryI bought 3 cans of this primer: one was a waste, as the tip clogged and replacing it didn’t work; one sprayed less than half the contents before the tip clogged; one worked well. Too bad, as the primer does offer what seems to be a high build, but I wasted too much money on defective cans.
Date published: 2021-07-09
Rated 1 out of 5 by Daytona from Very poor productHad a small project that didn’t warrant setting up my spray gun, so I bought this high build primer. At first it just sprayed clear, very little coverage or fill, so I thought I needed to shake the can for a few more minutes. Finally I started to get some coverage spraying at 4 to 5 inches, so it took time to cover. Next, the spay tip started to sputter, so I removed it and cleaned it out. It worked for awhile but then would simply stop spraying. I had bought a second can and that worked a bit better, but still had the coverage problem. The first can never worked again so I tried swapping tips, but that didn’t work so I finally had to toss the half full can.The product did wet sand easily, but didn’t fill-build the surface very well. What I had was more like an expensive guide coat. Total waste of money and time. Back to the spray gun.
Yes, body filler can be applied over Eastwood High Build Primer, but make sure to scuff or sand the primer before applying filler for good adhesion. Always follow proper drying and curing times for both the primer and filler.
Answered by: James Project Advisor
Date published: 2025-05-12
Can I use Kem Lustral enamel on top of this primer?
Asked by: Kyle
The advice is, can be top coated with all 1K, 2K, Solvent based and Waterbourne Paints. Recommend trying a small area to test compatibility of enamel.
Answered by: Bill G Tech Advisor
Date published: 2025-03-27
what primer should I use before laying down floor insulation
Asked by: joey
High build primer works if you installing Xmat or other installation.
Answered by: Anonymous
Date published: 2023-03-24
Is this considered a sealer primer? Every say I have to put a sealer primer on before final top coat, is this true?
Apply up to 2-3 coats (Allow 5-10 mins between each coat) Optimum Application temperature is 64-77F at 40-50% Humidity Tack Free 7-10 Minutes, Sand after 60 Mins Can be top coated with all 1K, 2K, Solvent based and Waterbourne Paints Wet Sand or Dry Sand with P400-P600
*Note: Specifications are approximate and subject to change.
